Item type |
デフォルトアイテムタイプ_(フル)(1) |
公開日 |
2023-03-18 |
タイトル |
|
|
タイトル |
超臨界流体によるpoly(ethylene terephthalate)のマイクロセルラープラスチックス製造に関する基礎的研究 <論文> |
|
言語 |
ja |
タイトル |
|
|
タイトル |
A Fundamental Study for Microcellular Poly (ethylene telephtalate) Production Using Supercritical Fluids |
|
言語 |
en |
作成者 |
佐藤, 善之
近常, 哲也
林, 一成
滝嶌, 繁樹
舛岡, 弘勝
山本, 博一
高杉, 雅信
|
アクセス権 |
|
|
アクセス権 |
open access |
|
アクセス権URI |
http://purl.org/coar/access_right/c_abf2 |
権利情報 |
|
|
権利情報 |
Copyright (c) 2004 社団法人 プラスチック成形加工学会 |
権利情報 |
|
|
権利情報 |
本文データはJournal@rchiveから複製したものである |
主題 |
|
|
主題Scheme |
Other |
|
主題 |
Cell structure , Volumetric expansivity , Poly (ethylene terephthalate) , Solubility , Crystallinity |
主題 |
|
|
主題Scheme |
NDC |
|
主題 |
570 |
内容記述 |
|
|
内容記述 |
Poly (ethylene terephthalate) (PET) foam was produced with a batch-wise method using carbon dioxide and nitrogen as physical blowing agents. Saturation pressure and temperature dependence of the foam structure was investigated. Solubility of the gases in PET and crystallinity of the PET induced by gas sorption were also investigated. PET foamed with CO2 at 323K and pressures higher than 10MPa had very fine cell structure (cell number density of 1012cm-3 and average cell diameter of 0.4μm). On the other hand, pressure dependence of the cell structure foamed with N2 was similar to results of amorphous polystyrene foam, whose cell structure became fine with increasing pressure. Volumetric expansivity of the PET+CO2 system rapidly decreased with increasing pressure, whereas that of the PET+N2 system gradually increased with increasing pressure. Cell structure foamed with CO2 became coarse with increasing saturation temperature. In the case of N2, saturation temperature dependence of cell structure was not observed at higher than 400K regardless of the solubility increase. These results suggested that cell structure and volumetric expansivity related not only to crystallinity but also to crystalline structure. |
|
言語 |
en |
出版者 |
|
|
出版者 |
プラスチック成形加工学会 |
言語 |
|
|
言語 |
jpn |
資源タイプ |
|
|
資源タイプ識別子 |
http://purl.org/coar/resource_type/c_6501 |
|
資源タイプ |
journal article |
出版タイプ |
|
|
出版タイプ |
VoR |
|
出版タイプResource |
http://purl.org/coar/version/c_970fb48d4fbd8a85 |
関連情報 |
|
|
|
識別子タイプ |
DOI |
|
|
関連識別子 |
10.4325/seikeikakou.16.247 |
関連情報 |
|
|
|
識別子タイプ |
DOI |
|
|
関連識別子 |
http://dx.doi.org/10.4325/seikeikakou.16.247 |
収録物識別子 |
|
|
収録物識別子タイプ |
ISSN |
|
収録物識別子 |
0915-4027 |
収録物識別子 |
|
|
収録物識別子タイプ |
NCID |
|
収録物識別子 |
AN10278882 |
開始ページ |
|
|
開始ページ |
247 |
書誌情報 |
成形加工
成形加工
巻 16,
号 4,
p. 247-253,
発行日 2004-04-20
|
旧ID |
30487 |