WEKO3
アイテム
Identification of Rotary Axis Location Errors under Spindle Rotation by using a Laser Barrier Tool Measurement System: Experimental Comparison with R-Test
https://hiroshima.repo.nii.ac.jp/records/2009084
https://hiroshima.repo.nii.ac.jp/records/2009084230639a5-3bf9-48b1-8b82-b89e9bd3c0c8
| 名前 / ファイル | ライセンス | アクション |
|---|---|---|
TISCIE_34_81.pdf (1.5 MB)
|
| Item type | デフォルトアイテムタイプ_（フル）(1) | |||||||||
|---|---|---|---|---|---|---|---|---|---|---|
| 公開日 | 2023-03-18 | |||||||||
| タイトル | ||||||||||
| タイトル | Identification of Rotary Axis Location Errors under Spindle Rotation by using a Laser Barrier Tool Measurement System: Experimental Comparison with R-Test | |||||||||
| 言語 | en | |||||||||
| 作成者 |
Ibaraki, Soichi
× Ibaraki, Soichi
× Yanai, Eita
|
|||||||||
| アクセス権 | ||||||||||
| アクセス権 | open access | |||||||||
| アクセス権URI | http://purl.org/coar/access_right/c_abf2 | |||||||||
| 権利情報 | ||||||||||
| 権利情報 | © 2021 The Institute of Systems, Control and Information Engineers | |||||||||
| 主題 | ||||||||||
| 主題Scheme | Other | |||||||||
| 主題 | machine tool | |||||||||
| 主題 | ||||||||||
| 主題Scheme | Other | |||||||||
| 主題 | metrology | |||||||||
| 主題 | ||||||||||
| 主題Scheme | Other | |||||||||
| 主題 | thermal deformation | |||||||||
| 主題 | ||||||||||
| 主題Scheme | Other | |||||||||
| 主題 | error calibration | |||||||||
| 主題 | ||||||||||
| 主題Scheme | Other | |||||||||
| 主題 | five-axis | |||||||||
| 主題 | ||||||||||
| 主題Scheme | Other | |||||||||
| 主題 | tool measurement | |||||||||
| 内容記述 | ||||||||||
| 内容記述 | Position and orientation errors of rotary axis average lines are often dominant error sources in the five-axis machining. Many schemes have been studied, and some are now commercially available, such that they can be identified on-machine, and then numerically compensated, by a machine tool user. Many conventional schemes install a measuring instrument or a measured target in a machine spindle, and thus cannot be performed when the spindle is rotating. Rotary axis location errors are often influenced by the machine’s thermal deformation. When the spindle is not rotating, they can be different from actual machining operations. This paper presents the application of a non-contact laser barrier tool measurement system to the identification of rotary axis location errors, when the spindle rotates in the same speed as in actual machining applications. An experimental thermal test is presented to observe the change in rotary axis location errors under continuous machine warm-up by spindle rotation and reciprocal linear axis motions. Experimental comparison with the R-Test, a typical conventional scheme that can be performed only when the spindle does not rotate, shows that rotary axis location errors change quickly after the machine warm-up is terminated. | |||||||||
| 言語 | en | |||||||||
| 出版者 | ||||||||||
| 出版者 | システム制御情報学会 | |||||||||
| 言語 | ||||||||||
| 言語 | eng | |||||||||
| 資源タイプ | ||||||||||
| 資源タイプ識別子 | http://purl.org/coar/resource_type/c_6501 | |||||||||
| 資源タイプ | journal article | |||||||||
| 出版タイプ | ||||||||||
| 出版タイプ | VoR | |||||||||
| 出版タイプResource | http://purl.org/coar/version/c_970fb48d4fbd8a85 | |||||||||
| 関連情報 | ||||||||||
| 識別子タイプ | DOI | |||||||||
| 関連識別子 | 10.5687/iscie.34.81 | |||||||||
| 関連情報 | ||||||||||
| 識別子タイプ | DOI | |||||||||
| 関連識別子 | https://doi.org/10.5687/iscie.34.81 | |||||||||
| 収録物識別子 | ||||||||||
| 収録物識別子タイプ | ISSN | |||||||||
| 収録物識別子 | 1342-5668 | |||||||||
| 収録物識別子 | ||||||||||
| 収録物識別子タイプ | ISSN | |||||||||
| 収録物識別子 | 2185-811X | |||||||||
| 収録物識別子 | ||||||||||
| 収録物識別子タイプ | NCID | |||||||||
| 収録物識別子 | AN1013280X | |||||||||
| 開始ページ | ||||||||||
| 開始ページ | 81 | |||||||||
| 書誌情報 |
システム制御情報学会論文誌 Transactions of the Institute of Systems, Control and Information Engineers 巻 34, 号 3, p. 81-88, 発行日 2021-03-15 |
|||||||||
| 旧ID | 51378 | |||||||||
